Bottom Brackets

Shimano Dura-Ace BB92, BB9000 Hollowtech II Bottom Brackets

BSA Bottom Bracket

Surly OD Bottom Brackets - Compatible with 24mm spindles - Moonlander BB fits a 100mm bottom bracket shell, but exterior width conforms to BB121 standard

- Ceramic bottom bracket for DUB spindle cranks Specs: - BB Shell Type: BB30 - BB Shell Width: 68/73mm - BB Bearing: Ceramic - Crank Spindle Diameter: 28.99mm - Interface: DUB - Cup Diameter: 42mm

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Compatible with Cannondale Ai frames - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

The PF4130 bottom bracket is Press Fit into 41mm diameter shells that are 86.5mm wide and mate most cranks with a 30mm spindle to that standard. If you have a BB86 frame and want to install a 386EVO crank or Rotor 30mm crank, this is the kit you need. CeramicSpeed bearings are installed in cups. The Standard Bearing has ceramic CeramicSpeed balls and hardened-steel races. The Coated Bearing has the same balls running on hardened-steel races with a 3-micron-thick metallic coating making the races harder and smoother, increasing service life and reducing friction. Enjoying the benefit of a massive, strong, and light 30mm crank spindle in your BB86 frame is possible with this kit. Press in the cups, set up the wave washer, add spacers if necessary, and torque down. CeramicSpeed's bottom bracket is also stiff and light, but its greatest benefits come in the form of drag reduction. Standard Bearings with stock grease typically have frictional drag of 0.3-0.4 watts per set. That's about a 75% drag reduction compared to conventional bottom brackets. The bearings also last at least three times longer than other bearings. Performance can be tuned by replacing grease. All Round comes with this BB, but you can change it to TT and Track Grease for less drag or to LongLife for greater durability. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Plastic cable protector - 10ml syringe All Round Grease - Sticker sheet

Features three sealed cartridge bearings. - Fits Daytona, Racing Triple, Centaur, Veloce and Mirage, 1193 and later Athena and pre-1995 Record and Chorus - 115mm spindle recommended for triple cranks and 32 or 35mm seat tubes - Unique taper is not compatible with Shimano - Weight: 233 grams

Compatible only with Record or Chorus square taper cranks. Features three cartridge bearings and a chromoly steel spindle. - 3 sealed cartridge bearings, 2 on the drive side, 1 on the non-drive side - Removable cups are machined from 7000 series aluminum - Unique taper is not compatible with Shimano - Weight: 220 grams

- Adapts ISCG-05 mount chainguide arms to fit flange or lockring style bottom brackets

Wheels Mfg solution for running a 30mm spindle crankset in a BSA threaded frame. Machined aluminum cups thread in to a standard threaded frame and feature Enduro 6806 ABEC-3 sealed bearings outboard of the BB shell. Fully serviceable. Notes: - For use with BB30 Wide 30mm diameter cranks with a spindle length of at least 104mm. - Will not work with standard BB30 cranksets. PLEASE MEASURE YOUR BB30 CRANK SPINDLE LENGTH! - Use only bottom bracket tools compatible with 16-notch MegoEvo BB’s. (FSA MegaEvo and Park Tool BBT-29). - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: BB30 Wide, BB30a, 386EVO, Rotor 3D+, SRAM BB30 Wide - Crank Spindle Diameter: 30mm - Crank Spindle Length: At least 104mm - Weight: 100g

BBRight™ Outboard bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 148g

Thread together BB for 386EVO frames and 24mm diameter spindle cranks. Machined aluminum cups thread together for stability, increased bearing life, and simple installation and maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB386EVO, BB392EVO - Bottom Bracket Shell Width: 86.6mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Diameter: 24mm - Over Bearing Width: 91.5mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Weight: 133g

Sealed and Delivered Bottom brackets are something you never think about until you do. With superior sealing and cable routing clearance, our 30mm Cinch BB92 will give you true peace of mind. This bottom bracket stands for precision and and durability. All About The Ball Bearings This BB uses 6806 retainer bearings packed with waterproof grease, along with improved wiper seals to ensure above-and-beyond durability and performance. Death to Creaks We fired up the ol' CNC machine to make sure the anodized alloy cups of this bottom bracket provide an exact, perfectly quiet fit in your frame. Weather, Or Not Features a built-in telescopic sleeve with improved sealing, keeping moisture from bearings and crank spindle. Plus, the sleeve provides more space for internal cable routing.

Shimano cranks fit into BB86 frames when you have this CeramicSpeed Bottom Bracket installed. The kit consists of two cups that are pressed into either side of the central opening. The cups come with CeramicSpeed Bearings installed. There are two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second version is our coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket works with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That represents an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature the CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box: - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of All Round Grease - Sticker sheet

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing SRAM DUB Compatible cranks in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames. Bottom Bracket Includes: - BB Cups with bearings - 2x - Silicone dust seals - 2x - 0.5mm crank spindle spacers - 2x - 1.0mm crank spindle spacers - 1x - 2.5mm crank spindle spacer - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm Asymmetrical - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields. - Crank Spindle Diameter: 29mm - Tool Pattern: 48.5mm x 16 notch - Weight: 158g

- Spindle Interface Type: 386 EVO - BB Shell Width: 68mm - Bottom Bracket Shell I.D.: 46mm - BB/Frame Interface: T47 - Weight: 95g

Convert your PF30 frame to a single-speed setup with our simple to use bottom bracket. Enduro Angular Contact sealed bearings. Double lip seals on all bearings with high fill rate top quality grease for maximum durability. Machined aluminum cups are superior in function and durability to plastic. Fully serviceable. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Chain Adjustment: 12mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 182g

A variant of the external bottom bracket, PressFit cut weight by up to 40 grams and provide easier installation by allowing you to press the bearing cups into the frame instead of threading them. There's no change to the crank — spindle length and diameter remain the same. - BB Shell Width (mm): 104.5 mm , 107 mm

- Standard JIS square taper with steel cups, retainers, lockrings, CrMo spindle, shield included - Formerly called CBB-ST, renamed CBBF

WeThePeople's Compact Mid Bottom Bracket uses high-quality precision sealed bearings for use with Mid-size bottom bracket shells. It includes their own 6061 alloy tube spacer and comes with a selection of spacers to help you dial in your drivetrain.

The Wheels Mfg PF30 Outboard bottom bracket will give you all of the same benefits as their well-loved Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in PF30 frames without the need for adapters. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 158g

External English (BSA) threaded road bottom bracket for 68mm shells. Wheels Mfg uses only Enduro bearings and silicone seals for the most durable and smoothest bottom brackets available. Fully serviceable. Includes: (2) - Enduro Silicone dust seals (1) - 2.5mm aluminum BB cup spacer (2) - 0.5mm crank spindle spacers (2) - 1.0mm crank spindle spacers Direct replacement for SRAM/Truvativ GXP bottom brackets! - Bearings: Enduro ABEC-3 - Color: Gray - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: GXP (SRAM, Truvativ, Etc.) - Crank Spindle Diameter: 22/24mm - Weight: 111g

T47 threaded BB cups for running 22/24mm spindle (SRAM) cranks in T47 frames. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact (non-drive-side bearing: ABEC-3) - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm – 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.7mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 48.5mm x 16-notch

Specifically designed for installing 24.00mm spindle diameter cranks (Shimano, etc.) in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames without the need for any adapters. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means smooth operation, fast bearing replacement, and no more creaking. - Bearings: ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch Note: FSA MegaExo spindles can be between 24.00mm and 24.07mm in diameter. If your FSA spindle is 24.07mm, this BB will not work! Please purchase Wheels Mfg. FSA 24.07x37 ceramic hybrid bearings separately.

Wheels Mfg BB86/92 thread together bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB86, BB92 - Bottom Bracket Shell Width (mm): 86mm, 92mm, 89.5mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 106g

Campagnolo ProTech bottom brackets feature a patented external sealing ring design that protects a strong, resilient fiberglass-charged polyamide central tube from the harmful ingress of water, mud and grit. - Designed specifically for gravel riding and racing to protect against water, mud & grit

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor, to fit in the tight space of this 34mm spindle. Choose between two bearings types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our CeramicSpeed Balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Note that the threaded extensions of this BB's cups that thread into the frame are thin, as they need to fit a 30mm spindle inside the cups. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet - Spacertube

6061 CNC machined Alloy cups w/ Precision sealed bearings. - Bearings: 19mm mid sealed (x2) (with american cups) - Spindle: 19mm, 8 spline (included in kit) - Spacers: 6061 Alloy cones with 15/16"/19mm hat washer and 4x spacers included NOTE: These sealed American BB & American BB sealed upgrade kit (with 8-spline spindle) are designed to replace the 8 spline spindle and bearings of an unsealed American BB with a sealed version. Fits most complete bikes that come with unsealed American 19mm BB. 19mm Model does not come with a spindle.

High performing square bottom bracket interfaces with English frames. - Fits square-taper spindle cranksets - Alloy adjustable cups - Includes 2 axle bolts

The SRAM DUB bottom bracket series has a simple job— to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard - Significantly lighter than GXP system

- Forged steel body - Alloy cups - Chromoly spindle - Sealed bearings - Interface: English - Spindle Type: Square Taper JIS - Weight: 290-300 grams

- Die Cast then CNC-machined alloy bearing cups - Composite DI2 compatible adjustable center sleeve - 100mm for Fat Bikes - For use with 100mm MTB NBD MegaExo cranksets - Spindle Interface Type: FSA MegaExo - BB Shell Width (mm): 100 - Bottom Bracket Shell I.D.: 1.37 - BB/Frame Interface: English

The PF30 standard is widely used. To make it compatible with Shimano and other 24mm diameter cranks, as well as improve the system, select this bottom bracket. The package comes with two cups and CeramicSpeed Bearings installed. The cups have extended inner sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system while also eliminating spindle rub on internal cables. The cups mate with 24/22mm crank spindles. There are two bearing options. Both Standard and Coated Bearings feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional feature: a 3-micron thick metallic layer over the races. This addition makes the races smoother and harder, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. The CeramicSpeed Coated Bearings last even longer and feature even lower drag. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. All Round Grease is installed in the bearings. It can be replaced for lower-drag TT and Track Grease or higher-durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

- Replaces standard BB90/95 press-in bearings commonly found on Trek bicycles with a solid, unified thread-together bottom bracket interface - Thread-together bottom brackets provide a secure and stable shell interface for smoother operation and extended bearing life - OS versions are designed for use in frames with worn-out, oversized bottom bracket shells - Low-friction dual seals protect the bearings from harmful contaminants - Sealed premium bearings are serviceable - Models available for both Shimano HTII 24mm and SRAM GXP 22/24mm spindles - Requires a special tool for installation (P/N# 610756)

T47 threaded BB cups for T47 frames and 22/24mm spindle diameter SRAM GXP cranks. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, and an anti-seize compound compatible with titanium BB shells. Bottom Bracket Includes: - BB Cups with bearings - 2x Silicone dust seals - 2x 0.5mm crank spindle spacers - 2x 1.0mm crank spindle spacers - 1x 24mm ID wave washer Specifications: - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width (mm): 68mm - 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Crank Spindle Diameter: 22/24mm - Over Bearing Width: 91.7mm in 86.5mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields - Tool Pattern: 48.5mm x 16-notch - Weight: 129g

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Designed for use with SRAM Wide Cranksets - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

- Ceramic bottom bracket for DUB spindle cranks

Origin8's Revolvr BB386 Outboard Bottom Bracket features forged and CNC-machined AL6061 thread-in cups for a superior fit and noise-free operation. Low-friction dual seals protect the bearings from harmful contaminants, while sealed premium bearings are both serviceable and replaceable. - Designed for installing BB30 Wide or BB386 30mm spindle cranks into BSA threaded frames - For use with 30mm diameter cranks with a spindle length of at least 104mm - Shell: 68mm x 33.6-33.9mm - Interface: ISO/English or BSA Threaded (1.37" x 24TPI) - Spindle Type: BB30 Wide/BB386 30mm - Cup Material: AL6061 - Weight: 120g

T47 threaded BB cups for T47 frames and 30mm diameter spindle cranks. Cups have internal bearings, and can be used in BB shells with widths from 68mm to 132mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, and an anti-seize compound compatible with titanium BB shells. Bottom Bracket Includes: - BB Cups with bearings - 2x Silicone dust seals - 2x 0.5mm crank spindle spacers - 2x 1.0mm crank spindle spacers Specifications: - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width (mm): 68mm - 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Crank Spindle Diameter: 30mm - Over Bearing Width: 68mm in 68mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields - Tool Pattern: 48.5mm x 16-notch - Weight: 97g

Box Two 24mm External bottom brackets feature cold-forged, CNC-machined alloy cups, dual-labyrinth bearing covers, and precision sealed bearings. They are the perfect match to Box Three, Four cranks, and the ultimate upgrade to the budget BBs sold with most cranksets. Box Two, 24mm External Bottom Brackets, are designed to fit all 24-millimeter crank spindles and frames with 68 or 73 x BC 1.37-inch bottom bracket shells. Features: - Stable Outboard Bearing Position - Precision Abec-5 Sealed Bearings Compatibility: - Compatibility: Box Three, Box Four, Shimano HollowTech II, RaceFace X-Type - Material: 6061-T6 Aluminum - Shell Width: 68mm/73mm - Spindle Type: 24mm - Thread: 1.37 Inch x 24 TPI - Weight: 105 grams / 3.7 ounces Specs: Process: CNC-Machined Cups Material: - Cups: Alloy - Sleeve - ABS Plastic Finish: Anodized Spindle Type: 24mm Shell Width: 68/73mm Thread: 1.37 Inch x 24 TPI (English) Compatibility: - Shell: BSA (Euro) Threaded - Spindle: Box Three, Box Four, Shimano HollowTech II, RaceFace X-Type Weight (+/- 5%): 105 g / 3.7 oz

The Hellbender70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

The Hellbender 70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

SRAM's GXP PressFit Bottom Bracket Cups are the premium choice for getting the most out of every pedal stroke. They feature smooth bearings that keep drag to a minimum and seals that keep debris out. Plus, these BB cups press directly into the frame without having to be threaded in for reduced weight and enhanced durability.

T47 threaded BB cups for running 30mm spindle cranks in T47 frames. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm – 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.7mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 48.5mm x 16-notch

T47 threaded BB cups for running 24mm-spindle cranks in T47 frames. Cups have outboard bearings and are typically used in BB shells with widths from 68mm to 100mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68 – 100mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.2mm in 68mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16-notch

The SRAM DUB bottom bracket series has a simple job—to connect crankarms and protect the smooth, long-lasting application of power to the drivetrain. SRAM engineered the oversized DUB spindle to work across every bottom bracket standard, simplifying crankarm compatibility. - Compatible with Cannondale Ai frames - Gutter Seal Technology drastically improves sealing against the elements - Sealed cartridge bearings - One oversized spindle to work across every bottom bracket standard

Origin8's Revolvr BB86/92 Thread-Together Bottom Bracket provides a secure and stable shell interface for smoother operation and extended bearing life. Hybrid AL6061/Nylon fiber cups offer a superior fit and noise-free operation. Low-friction dual seals protect the bearings from harmful contaminants, while sealed premium bearings are both serviceable and replaceable. Models are available for both Shimano HTII 24mm and SRAM GXP 22/24mm spindles. - Replaces all standard BB86/92 press-fit bottom brackets - Shell: 86-92mm x 41mm - Interface: BB86/BB92 - Cup Material: AL6061/Nylon Fiber - Weight: 103g

FSA (Full Speed Ahead) MegaExo 19 bottom brackets are for use with 19mm diameter spindles. - For Alloy Cranks with MegaExo 19 BB-AL86/19/SLE - Spindle Interface Type: FSA MegaExo 19 - BB Shell Width: 86mm - Bottom Bracket Shell I.D.: 41 - BB/Frame Interface: BB86

Wheels Mfg solution for running a 30mm spindle crankset in a BSA threaded frame. Machined aluminum cups thread in to a standard threaded frame and feature Enduro 6806 ABEC-3 sealed bearings outboard of the BB shell. Fully serviceable. Notes: - For use with BB30 Wide 30mm diameter cranks with a spindle length of at least 104mm. - Will not work with standard BB30 cranksets. PLEASE MEASURE YOUR BB30 CRANK SPINDLE LENGTH! - Use only bottom bracket tools compatible with 16-notch MegoEvo BB’s. (FSA MegaEvo and Park Tool BBT-29). - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: ISO/English or BSA Threaded (1.37 in x 24 TPI) - Bottom Bracket Shell Width (mm): 68mm - Bottom Bracket Shell I.D.: 33.6-33.9 mm - Crank Spindle Type: BB30 Wide, BB30a, 386EVO, Rotor 3D+, SRAM BB30 Wide - Crank Spindle Diameter: 30mm - Crank Spindle Length: At least 104mm - Weight: 102g

This bottom bracket is perfect for when you have a PF30, BBright, or 386EVO shell frame and want to install a crank with a 30mm spindle into the frame. All these frame standards have a 46mm inner diameter and smooth insides, though the widths vary from 68mm to 86mm. This bottom bracket features nearly zero loss of power due to friction, thanks to the CeramicSpeed's incredibly efficient bearings. Choose either our Standard or Coated Bearings—both have super-round, super-smooth CeramicSpeed balls rolling on hardened-steel races. The Coated version has a metallic coating laid onto the races, making them even harder and smoother and resulting in longer life and lower drag. They come installed in cups. 30mm spindles on cranks are increasingly popular because of the high stiffness and low weight. 46mm inner diameter bottom brackets are popular for the freedom they offer designers in building frames. Because of the variety of widths, the cups here extend into the shell and come with a telescoping spacer tube to further seal and stiffen the system. The bottom bracket is already stiff thanks to hard ceramic bearings and hardened-steel races. Thanks to CeramicSpeed, it also generates nearly zero drag. Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction versus conventional BBs. The bearings also last at least 3x longer than other bearings. You can change the grease to fine-tune your BB's performance characteristics. TT and Track, All Round, and LongLife are greases CeramicSpeed designed. The first has the least drag, while the last is the most durable. All Round, in the middle, comes standard in road bearings. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Spacer tube - 10ml All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BSA for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BSA - Opening diameter: Threaded - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Spacertube

- For 19mm crank spindles and Euro bottom bracket frames - Sealed quad bearing design with alloy cups - Shell: Euro - Interface: English - Spindle Type: 19mm

BB90 is the Trek oversized bottom bracket standard and is only found on Trek road bikes. The shell is 90.5mm wide and is designed to work with 24mm spindles and road cranks and have the bearings inside the shell. The CeramicSpeed Bearings come as two bearings, which are then pressed into the frame. Those two bearings consist of either CeramicSpeed Standard or Coated Bearings. Both feature super smooth, super-round CeramicSpeed Balls contained in hardened-steel races. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. -BB90 is simple and light. The standard is designed to work with 24mm spindles. The bearings work with Shimano and other 24mm cranks, like FSA. - The CeramicSpeed Standard Bearings last at least 3 times longer than other bearings. That's thanks to hardened-steel races and CeramicSpeed Balls that are 100% smoother & 15% harder than the ceramic competition. These bearings have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to stock BBs. - The CeramicSpeed Coated Bearings reduce drag by 50% compared to Standard Bearings and an improvement in bearing life of 60%. In The Box: - 2 BB90 bearings - 2 seals - 2 dust covers with integrated spacers - 10ml syringe of All Round Grease - Sticker Sheet

Origin8's Revolvr BB86/92 Press-Fit Bottom Bracket features precision-machined AL6061 cups for a superior fit and noise-free operation. Low-friction dual seals protect the dual-row premium flanged bearings from harmful contaminants. - Designed for installing BB30 Wide, BB386, BB392, and other 30mm spindle cranks into BB86/92 frames - For use with 30mm diameter cranks with a spindle length of at least 104mm - Shell: 86-92mm x 41mm - Interface: BB86/BB92 - Spindle Type: BB30 Wide/BB386 30mm - Cup Material: AL6061 - Weight: 80g

FSA MegaExo Bottom Brackets - MegaExo cranks to press fit BB86 frame - Spindle Interface Type: FSA MegaExo - BB Shell Width: 86mm - Bottom Bracket Shell I.D.: 41 - BB/Frame Interface: BB86

- American style BB for older 3-piece cranks - American BB for 3-piece cranksets - Fits 68mm American frames - Steel construction - Weight: 517 grams - Shell: 68mm - Interface: 24 tpi - Spindle Type: SQR JIS - Cup Material: Steel

The Problem Solvers Bushnell Eccentric Bottom Bracket is the industry leading design for chain tension adjustment on tandem and dedicated single speed bikes equipped with eccentric bottom bracket shells. The classic version features full-body, aluminum construction across the shell for maximum surface area friction and additional value. The Bushnell Fat Bike Eccentric Bottom Bracket is designed for the 100mm shells in most fat bikes. - Accepts English threaded bottom bracket cups - Classic, full-body design - Diameter of part - 2.118 inches (53.78mm) - Fits BB shells from 53.8 ~ 54mm I.D. without shim - Fits BB shells up to 100mm width

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The PF30 for SRAM DUB Road comes in two versions. One version uses our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: PF30 - Opening diameter: 46mm - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

As The Wheel Turns This trusty 30mm workhorse of a bottom bracket is built with custom RF double row cartridge bearings for trouble-free, long haul rolling for you PF41 frame. In A Sea Of Bearings These little buggers can make a huge difference, so we've made sure our double row custom retainer bearings are super durable and up for the long run. Close Enough Won't Cut It These precision steel cup are coated for corrosion resistance, and CNC-ground surfaces of this bottom bracket provide an exact, perfectly quiet fit in your frame. Weather, Or Not All RF bottom brackets come with an inner plastic sleeve to keep the elements out and include all appropriate spacers to ensure a versatile fit.

SRAM's GXP PressFit Road Bottom Bracket Cups are the premium choice for getting the most out of every pedal stroke. They feature smooth bearings that keep drag to a minimum and seals that keep debris out. Plus, these BB cups press directly into the frame without having to be threaded in for reduced weight and enhanced durability.